The New CFPS 2026 Updated Verified Study Guides & Best Courses [Q71-Q94]

Share

The New CFPS 2026 Updated Verified Study Guides & Best Courses

Authentic CFPS Exam Dumps PDF - 2026 Updated

NEW QUESTION # 71
Which OSHA regulation addresses storage and handling of liquefied petroleum gas?

  • A. 1910.107
  • B. 1910.108
  • C. 1910.119
  • D. 1910.110

Answer: D

Explanation:
OSHA regulation 1910.110 addresses storage and handling of liquefied petroleum gas (LPG). This regulation covers the general requirements for the design, construction, installation, operation, inspection, and maintenance of LPG systems, including containers, piping, valves, fittings, regulators, burners, and appliances. The regulation also specifies the safety precautions and procedures for the prevention of fire and explosion hazards involving LPG. The regulation applies to all employers who store, handle, or use LPG in their workplaces. Reference:
OSHA: 1910.110 - Storage and handling of liquefied petroleum gases 1
Nebula Safety: Storage & Handling of Liquefied Petroleum Gases (LPGs) 2


NEW QUESTION # 72
On the Homeland Security color-coded threat-level system, what color code represents the most severe risk?

  • A. Green
  • B. Yellow
  • C. Red
  • D. Orange

Answer: C


NEW QUESTION # 73
What percent of fire departments surveyed participate in the delivery of emergency medical services?

  • A. 79%
  • B. 90%
  • C. 61%
  • D. 38%

Answer: A

Explanation:
79% of fire departments surveyed participate in the delivery of emergency medical services (EMS). This is based on the NFPA report "US Fire Department Profile 2020" 1, which states that nationwide, 37% of fire departments provided no EMS, 46% provided basic life support (BLS), and 17% provided advanced life support (ALS). Therefore, the percentage of fire departments that provided either BLS or ALS is 46% + 17% = 63%. However, this does not include fire departments that provided EMS through a third-party contract or agreement. According to the NFPA fire service survey from 2018-2020 2, 16% of fire departments reported having such an arrangement. Therefore, the percentage of fire departments that participated in the delivery of EMS in some form is 63% + 16% = 79%. Reference:
NFPA report - U.S. fire department profile 3
US Fire Department Profile 2020 Supporting Tables 2


NEW QUESTION # 74
Evaluating fire for probability as a sequence of outcome is accomplished through which of the following?

  • A. Action matrix
  • B. After action review
  • C. Pre-event analysis
  • D. Event tree

Answer: C

Explanation:
http://www.nfpa.org/Assets/files/AboutTheCodes/921/Ch%204%20methodology.pdf


NEW QUESTION # 75
Which of the following statements about smoke detectors is FALSE?

  • A. Detectors using the cloud chamber principle also make use of the photoelectric principle.
  • B. Detectors using the ionization principle provide somewhat faster response to high-energy (open flaming) fires.
  • C. Detectors using the photoelectric principle also use a small amount of radioactive material.
  • D. Detectors using the photoelectric principle provide somewhat faster response to low-energy (smoldering) fires.

Answer: C

Explanation:
Detectors using the photoelectric principle do not use a small amount of radioactive material. This is a false statement about smoke detectors. Detectors using the photoelectric principle use a light source and a light sensor to detect the presence of smoke. When smoke enters the detection chamber, it scatters the light and triggers the alarm. Detectors using the photoelectric principle are more responsive to low-energy (smoldering) fires that produce large smoke particles 12.
Detectors using the cloud chamber principle also use the photoelectric principle. This is a true statement about smoke detectors. Detectors using the cloud chamber principle use a sealed chamber that contains a supersaturated vapor. When smoke enters the chamber, it causes the vapor to condense into droplets that reflect light. The light is then detected by a photoelectric sensor that activates the alarm. Detectors using the cloud chamber principle are very sensitive to small smoke particles 34.
Detectors using the ionization principle provide somewhat faster response to high-energy (open flaming) fires. This is a true statement about smoke detectors. Detectors using the ionization principle use a small amount of radioactive material that ionizes the air in the detection chamber. When smoke enters the chamber, it reduces the ionization and the electric current. The drop in current is then detected by a circuit that activates the alarm. Detectors using the ionization principle are more responsive to high-energy (open flaming) fires that produce small smoke particles 12.
Detectors using the photoelectric principle provide somewhat faster response to low-energy (smoldering) fires. This is a true statement about smoke detectors. Detectors using the photoelectric principle use a light source and a light sensor to detect the presence of smoke. When smoke enters the detection chamber, it scatters the light and triggers the alarm. Detectors using the photoelectric principle are more responsive to low-energy (smoldering) fires that produce large smoke particles 12.


NEW QUESTION # 76
What is the maximum allowable sound pressure level (SPL) for a fire alarm system?

  • A. 100 dBA
  • B. 50 dBA
  • C. 30 dBA
  • D. 130 dBA

Answer: A

Explanation:
According to NFPA 72, the maximum sound pressure level (SPL) for a fire alarm system is 110 dBA at the minimum hearing distance from the audible appliance 1. However, this limit can be exceeded if the sound pressure level measured 2 000 mm above floor level is not more than 100 dBA 2. Sound pressure level is a measure of the intensity of sound at a given point in space, expressed in decibels (dB). The higher the SPL, the louder the sound. For comparison, a normal conversation is about 60 dB, a jet engine is about 140 dB, and a gunshot is about 160 dB 3. Reference: Sound Pressure Levels - NFPA; NFPA fire alarm sound level - EntirelySafe.com; Subsection 907.5 - Occupant notification systems - Casetext; How Loud Is a Fire Alarm In Decibels (dB)? With Noise Comparison Chart; The Ontario Building Code | Audibility of Alarm Systems.


NEW QUESTION # 77
NFPA 3000, Standard for an Active Shooter/Hostile Event Response (ASHER) Program contains the following as four mam concepts: Whole Community Unified Command. Integrated Response and_______,

  • A. Prevention
  • B. Planned Recovery
  • C. Defensive Strategy
  • D. Mitigation

Answer: B


NEW QUESTION # 78
How many additional switches or circuit breakers are allowed for a separate service?

  • A. 0
  • B. 1
  • C. 2
  • D. 3

Answer: B

Explanation:
Explanation
According to NFPA 70: National Electrical Code (NEC) 2020 Edition, Article 230.71(A), each service shall have only one disconnecting means unless the requirements of 230.71(B) are met, which provide four specific service configurations. In each configuration, there shall be not more than six switches or sets of circuit breakers, or a combination of not more than six switches and sets of circuit breakers, per service grouped in any one location. Therefore, the maximum number of additional switches or circuit breakers allowed for a separate service is six.References:
NFPA 70: National Electrical Code (NEC) 2020 Edition, Article 230.71(A) and (B)12 ElectricalLicenseRenewal.com, 230.71 Maximum Number of Disconnects3


NEW QUESTION # 79
What type of detector is constructed using a stainless steel tubing or outer later over a ceramic thermistor core protecting a center conductor?

  • A. Line-type/bnear heat detector
  • B. Spot heat detector
  • C. Bimetallic neat detector
  • D. Fiber optic neat detector

Answer: A


NEW QUESTION # 80
Which is a sign of exposure to cyanide gas?

  • A. Vomiting with great force
  • B. Collapsing suddenly
  • C. Sweating profusely
  • D. Gasping for air

Answer: D


NEW QUESTION # 81
When conducting a needs assessment for a fire department, what term describes the level of harm associated with exposure to a fire or its effluent?

  • A. Risk
  • B. Hazard
  • C. Hazard Analysis
  • D. Strategic Plan

Answer: C


NEW QUESTION # 82
Besides smoke detection what other permitted detection for Phase 1 elevate recall is typically used m ambient conditions?

  • A. Carbon monoxide defector
  • B. Bean detector
  • C. Heat detector
  • D. Smoke detector

Answer: C


NEW QUESTION # 83
What data analysis approach provides the broadest perspective of a fire problem?

  • A. Data re-examination
  • B. Trend analysis
  • C. Scenario groupings
  • D. Top-down approach

Answer: D

Explanation:
Scenario groupings is a data analysis approach that provides the broadest perspective of a fire problem by identifying and comparing different types of fire incidents based on their characteristics, such as ignition source, fuel, location, time, and outcome. This approach can help reveal patterns, trends, and relationships among fire scenarios and support fire prevention and protection strategies. Reference: Fire Data Analysis Handbook, Chapter 5: Scenario Groupings; [Fire Protection Handbook], Section 2, Chapter 3: Fire Data Collection and Analysis.


NEW QUESTION # 84
What kind of agent is anthrax?

  • A. Infectious disease
  • B. Chemical asphyxiant
  • C. Neurotransmitter
  • D. Blood agent

Answer: D


NEW QUESTION # 85
What is the maximum allowable travel distance from any part of a smoke compartment to the door in a smoke barrier in a new health care facility?

  • A. 50 ft. (15 m).
  • B. 200 ft. (60 m).
  • C. 150 ft. (46 m).
  • D. 100 ft.(30 m).

Answer: B

Explanation:
Explanation
The maximum allowable travel distance from any part of a smoke compartment to the door in a smoke barrier in a new health care facility is 200 ft. (60 m). This is based on NFPA 101: Life Safety Code, 2018 Edition, Chapter 18, Section 18.3.7.3, which states that "the travel distance from any point in a smoke compartment to reach a door in the required smoke barrier shall not exceed 200 ft (61 m)." A smoke compartment is a space within a building that is enclosed by smoke barriers on all sides, including the top and bottom. A smoke barrier is a continuous membrane, or a combination of materials, that is designed to restrict the movement of smoke.A smoke barrier door is a door assembly that is installed in a smoke barrier to allow access between smoke compartments123


NEW QUESTION # 86
Wildfires can have far-reaching impacts on the natural environment. Which tool can help land managers to create plans for landscape repair to minimize post-fire impacts on water supplies and other sensitive ecosystems?

  • A. Early detection cameras
  • B. Deployable heat detectors
  • C. Satellite imagery
  • D. Electronic data collection

Answer: C


NEW QUESTION # 87
What are the minimum secondary power supply requirements for a protected premises system?

  • A. 24 hours of standby power followed by 1 hour of emergency operation
  • B. 24 hours of standby power followed by 2 hours of emergency operation
  • C. 24 hours of standby power followed by 5 minutes of alarm
  • D. 24 hours of standby power followed by 15 minutes at maximum connected load

Answer: A


NEW QUESTION # 88
The total complex of douses factories offices and schools in which we live and work is commonly known as______.

  • A. The community
  • B. The designed environment
  • C. The engineering domicile
  • D. The built environment

Answer: D


NEW QUESTION # 89
The primary design approach to mitigate the effect of wind on smoke movement in high-rise buildings is based on

  • A. height of the building.
  • B. tightness of the building.
  • C. fire department access.
  • D. outside temperature.

Answer: B

Explanation:
The tightness of the building affects the wind resistance and pressure distribution on the surface of the building, which in turn influences the smoke movement inside the building. According to NFPA 92, Standard for Smoke and Dust Control in Commercial Buildings, "The tightness of a building is determined by its structural system and construction materials. The tighter a building is, the less wind resistance it experiences."1 Reference: 1: NFPA 92, Standard for Smoke and Dust Control in Commercial Buildings, 2019 edition, Section 5.2.2.2.


NEW QUESTION # 90
Which limit point is considered the total head of a fire pump characteristic curve when it is operating at rated speed and there is no flow into the fire protection system?

  • A. Shutoff pressure
  • B. Net positive suction head
  • C. Rated flow and pressure
  • D. Overload point

Answer: A


NEW QUESTION # 91
Power for driving fire pumps is selected on the basis of reliability, adequacy, economy, and

  • A. adaptability.
  • B. efficiency.
  • C. ecology.
  • D. safety.

Answer: D

Explanation:
Explanation

Fire pump
Explore
The correct answer is B.Safety is one of the criteria for selecting the power source for driving fire pumps, according to NFPA 20, Chapter 9.1.1.11. Reliability, adequacy, and economy are the other criteria mentioned in the same chapter. Efficiency, adaptability, and ecology are not explicitly stated as criteria in NFPA 20, although they may be considered as secondary factors in some cases.
1:Pump Installation: Everything About Electric and Diesel Driven Fire ...


NEW QUESTION # 92
Which is the lead federal agency for consequence management during a terrorist incident?

  • A. FEMA
  • B. DHS
  • C. DOT
  • D. FBI

Answer: A


NEW QUESTION # 93
What NFPA document address carbon monoxide warning equipment?

  • A. NFPA 72
  • B. NFPA 720
  • C. NFPA 610
  • D. NFPA 1620

Answer: B


NEW QUESTION # 94
......


NFPA CFPS Exam Syllabus Topics:

TopicDetails
Topic 1
  • Detection and Alarm: In this topic, Fire protection consultants will need to demonstrate their expertise in the operational characteristics of fire alarm systems and detection technologies. They will be tested on their ability to apply relevant codes, inspect systems, and ensure compliance with safety standards.
Topic 2
  • Facility Fire Hazard Management: The exam will assess the proficiency of Fire protection consultants in managing and mitigating fire hazards in facilities through effective planning and system management. Candidates must demonstrate their understanding of architectural drawings, risk assessments, and the integration of fire protection systems to ensure safety across all building operations and emergency preparedness protocols.
Topic 3
  • Confining Fires: Fire protection consultants will be tested on their ability to recommend and ensure the proper installation and maintenance of fire-resistant construction, including firewalls and barriers. This section will assess their knowledge of smoke control methods and their ability to assist in the design of systems that limit fire spread, ensuring that buildings are equipped to confine fires and protect occupants.
Topic 4
  • Fire Suppression: This topic covers the knowledge of fire suppression systems, including routine maintenance, testing, and system design considerations. Fire protection consultants will be expected to demonstrate their ability to evaluate fire suppression systems, such as sprinklers and non-water-based systems, and ensure their proper functionality following codes and local policies.
Topic 5
  • Fire Prevention: Programs, Materials, Processes, and Environments: This topic assesses the capability of identifying fire hazards and applying mitigation strategies to minimize risks in a community or organization. Fire protection consultants will be tested on their ability to conduct safety audits, provide fire hazard training, and recommend safety tools and equipment.
Topic 6
  • Safety in the Built Environment: This topic will test the knowledge and skills of Fire protection consultants in evaluating and ensuring the proper application of fire protection systems in various buildings. They must demonstrate their ability to analyze fire safety protocols, building systems, and regulations for compliance.

 

Get Prepared for Your CFPS Exam With Actual 190 Questions: https://www.getvalidtest.com/CFPS-exam.html

Valid CFPS Test Answers Full-length Practice Certification Exams: https://drive.google.com/open?id=1F3zvWzx4s88sgDt5RZxKWbHz-2LCwCZT