[Nov 10, 2023] GetValidTest NS0-593 Exam Practice Test Questions (Updated 60 Questions)
Pass Network Appliance NS0-593 Exam Info and Free Practice Test
Network Appliance NS0-593 exam is designed for IT professionals who want to become a NetApp Certified Support Engineer ONTAP Specialist. NetApp Certified Support Engineer ONTAP Specialist certification is recognized globally and validates the candidate's skills and knowledge in supporting and troubleshooting NetApp ONTAP systems. The NS0-593 exam covers a wide range of topics related to NetApp ONTAP, including installation, configuration, management, and troubleshooting.
NEW QUESTION # 29
Your customer complains about missing volume snapshot copies on a SnapMlrror destination. While
investigating this case, you notice an executed SnapMirror resync operation in the event logs of the system.
In this scenario, what Is the cause of this problem?
- A. The autodelete option removed Snapshot copies before the resync.
- B. NetApp ON TAP System Manager removed these snapshot copies due to a snapshot schedule.
- C. Newer Snapshot copies than the common snapshot that was chosen for resync were removed
automatically at the destination. - D. Snapshot copies were manually removed from the destination after the resync.
Answer: D
NEW QUESTION # 30
A user mentions that their home drive, that Is an export within a volume, is no longer allowing them to save
files. The drive reports that it Is full, even though It shows that minimal data is written to it.
Which statement would explain this behavior?
- A. Other files within the volume are also owned by the user, exceeding the user quota.
- B. The client system needs to remount the export to show the proper space.
- C. The mount is stale and uses a cached version of the volume.
- D. Other users wrote to this user's home drive.
Answer: A
NEW QUESTION # 31
Your customer mentions that they have accidentally destroyed both rootaggregates in their two-node cluster.
In this scenario, what are two actions that must be performed? (Choose two.)
- A. Re-create the cluster from the remote backup.
- B. Re-create the cluster from the local backup.
- C. Rejoin the second node to the re-created cluster.
- D. Install ONTAP from a USB device.
Answer: C,D
NEW QUESTION # 32
A storage administrator reports that a monitoring toot is reporting that the storage controller reads between
90% to 93% CPU use. You run the sysstat -m command against thenode in question.
Referring to the exhibit, which statement is correct?
- A. The customer should be advised to exclude certain workflows to reduce use.
- B. You should immediately investigate further bygathering perfstat data and opening a support case.
- C. High network exempt use could be a problem.
- D. The CPU Is not a first-order monitoring metric for ONTAP.
Answer: B
NEW QUESTION # 33
A customer with an FC MetroClusterconfiguration that is running NetApp ONTAP 9.8 software experienced a
site outage and wants to know why the MetroClusler configuration did not switch over to the other site.
What are two reasons for this problem? (Choose two.)
- A. The site had unmirrored aggregates.
- B. There was a failed PSU inthe switchover site.
- C. An ISL link was not operating at 16Gbps.
- D. The ISLs were down between the sites.
Answer: A,B
NEW QUESTION # 34
Your customer is running a NetApp AFF A800 system with NetAppONTAP 9.8 software and states that their
NS224 shelf is not showing with the correct shelf ID. You analyze the data and the shelf shows an
identification of "1.SHFHUXXXXXXXXXX."
What is the cause of the reported Issue?
- A. The shelf had a disk replaced too quickly.
- B. The shelf was cabled Incorrectly.
- C. The shelf has been power cycled.
- D. A new shelf was added to the controller.
Answer: D
NEW QUESTION # 35
You have a NetApp ONTAP cluster consisting of four NetApp FAS8200 controllers with two NetApp
CN1610 cluster switches running ONIAP 9.8 software. You are receiving several alert messages stating that
the cluster network has degraded. After troubleshooting, you determine that the errors are being generated
fromNode 2, interface e0b.
In this scenario, what should you do first to solve this problem?
- A. Replace the motherboard on Node 2.
- B. Replace both NetApp CN1610 switches.
- C. Replace the Twinax cable between Node 2, Interface e0b. and the NetApp CN1610 switch.
- D. Replace the NetApp CN1610 switch that connects to Node 2, interface e0b.
Answer: A
NEW QUESTION # 36
Your customer calls you because one application is not able to access a NetApp ONTAP S3 bucket. While
reviewing the EMS log on the cluster, you see the following message:
The same credentials work in another application.
In this scenario, what would cause this problem?
- A. The application is using v4 signatures.
- B. The application is trying to log in as an anonymous user.
- C. The application is trying to access using the HTTP protocol.
- D. The application is using v2 signatures.
Answer: B
NEW QUESTION # 37
Your customer added a new DS4246 shelf to their FAS2750 single-node system and created a new aggregate
on the new shelf. Two weeks later, they log into Active IQ and discover the Medium Impact error shown
below.
Shelves with both connections via the same SAS path detected
Referring to the exhibit, which statement is correct?
- A. The cables are cabled Incorrectly on the SAS stack.
- B. Active IQ Is not aware of the shelf configuration for a single-node system.
- C. This situation is normal for a FA57750 single-node system.
- D. In a FAS2750 system, the internal shelf is only seen on one path, and the external shelves are seen on
two paths.
Answer: C
NEW QUESTION # 38
Your customer has deployed a two petabyte NetAppONTAP FlexGroup volume across their 4-node ONIAP
9.8 cluster. They plan to store over three billion files. They want to prevent file 10 conflicts since files are
placed into the FlexGroup volume.
In this scenario, which two NFS SVM parameters should be enabled? (Choose two.)
- A. -v4-64bit-idantifiers
- B. -v3-64bit-identifiers
- C. -v3-fsid-change
- D. -v4-fsid-change
Answer: B,C
NEW QUESTION # 39
A customer reports that some of their client computers are unable to access a FlexGroup over CIFS. This
problem involves only their older Windows XP clients and some printers and scanners.
In this scenario, which statement Is correct?
- A. These systems use the SMQI protocol which Is an unsupported feature in FlexGroup
- B. FlexGroup requires CIFS shares to use the Continuously Available Feature, which these clients do not
support. - C. FlexGroup requires CIFS shares to be located in qtrees, which these clients do not support.
- D. These systems use Offloaded Data Transfer, which is an unsupported feature in FlexGroup.
Answer: B
NEW QUESTION # 40
After expanding a two-node AFF A300 cluster with two AFF A700 nodes, you observe latencies when data is
accessed indirectly. The system node run -node -command netstat command shows retransmits and packet
drops on the LIFs. The AFF A700 nodes with 40 Gbps and the AFF A300 connect with 10 Gbps to the cluster
interconnect. You are using Cisco Nexus 3132Q cluster interconnect switches. You just updated to ONTAP
9.8 software.
In this scenario, what is causing this problem?
- A. There is an NXOS firmware mismatch, verify in the Interoperability Matrix (1MTJ for a supportedversion.
- B. AFF A300 and AFF A700 node mixing Isnot supported in ONTAP 9.8 software.
- C. The 10 Gbps to 10 Gbps cluster Interconnect is creating a speed mismatch.
- D. The AFF A300 Is using an adapter card for the cluster Interconnect, but only onboard ports are supported.
Answer: C
NEW QUESTION # 41
After a normal power down of both nodes forbuilding maintenance, Node01 of a 2-node cluster cannot be
powered back up; however, all disk shelves are powered.
Which action should be performed to bring the cluster online and allow Node02 to serve data?
- A. Recreate the cluster with the system configuration recovery cluster recreate -from node command.
- B. Reboot the node With the system node reboot -node Node02 -bypass-optimization true command.
- C. Reinitialize the cluster with option 4a from the boot menu.
- D. Perform a takeover with the storage failover takeover -ofnode Node01 -option forcecommand.
Answer: A
NEW QUESTION # 42
A system panic due to an "L2 watchdog timeout hard reset" error occurred. You have found a FIFO message
in the SP log.
Which FIFO message Is useful for Investigating this Issue?
- A. BIOS exit BBSP:C=2F L=20 FIFO: 2 C8 C9 C4 24 4 6 18 7 8 11
- B. before NMI BBSP:C=00 L=00 FIFO: F3 F2 F1 F0 5 B2 0 0 0 80 20 E F E3 C0 C2 3 4 6 7 9 9 A
- C. before Reset BBSP:C=00 L=00 FIFO:
- D. ONTAP Shutdown BBSP:C=00 L=2F FIFO:
Answer: A
NEW QUESTION # 43
A customer enabled NFSv4.0on an SVM and changed the client mount from NFSv3 to NFSv4. Afterwards,
the customer found that the directory owner was changed from root to nobody.
In this scenario, which statement is true?
- A. The ID mapping domains do not match between the client and server.
- B. The export policy is not configured properly.
- C. The clients must be restarted to start using NFSv4.
- D. The customer did not configure name services on the SVM.
Answer: B
NEW QUESTION # 44
Your customer noticed in NetApp Active IQ that their NetApp Cloud Volumes ONTAP forAzure HA solution
is no longer sending AutoSupport messages over HTTPS. A support ticket has been opened to find out why.
No changes have been made to the Cloud Volumes ONTAP for Azure HA environment.
In this scenario, which two autosupport command parameters should be used to validate that AutoSupport Is
working properly? {Choose two.)
- A. -to
- B. -proxy-url
- C. -transport
- D. -mail-hosts
Answer: B,D
NEW QUESTION # 45
You are attempting to connect a NetApp ONTAP cluster to a very complex network that requires LIFs to fail
over across subnets.
How would youaccomplish this task?
- A. Configure an equal number of UFs on each subnet.
- B. Configure a I IF failover policy for each subnet inside a single broadcast domain.
- C. Configure VIP LIFs using BGP.
- D. Configure VIP LIFs using OSPF.
Answer: C
NEW QUESTION # 46
An administrator receives the following error message:
What are two causes for this error? (Choose two.)
- A. An SSD disk is performing garbage collection to create a dense data layout.
- B. There Is excessive SSD load causing the wear leveling to become unbalanced.
- C. A disk is falling.
- D. There is excessive SATA HDD load.
Answer: B,D
NEW QUESTION # 47
A user reports that a colleague saved a file called Test.txt from a UNIX system to a multiprotocol volume.
When opening the file later from a Windows system, it was not the file that they wanted. The file that they
wanted was named TEST~1.TXT.
Which statement explains this behavior?
- A. Windows Volume Shadow Copy Service stored an older version of the file.
- B. UNIX name mapping updated the filename.
- C. A Snapshot copy preserved two versions of the file.
- D. Case Insensitivity of SMB clients caused the file to be displayed with a different name.
Answer: C
NEW QUESTION # 48
You recently discovered the error message shown below in your ONTAP logs.
What should be your first action to correct this Issue?
- A. Power cycle all the disk storage shelves that contain drives of the aggregate with the my_data_vol
volume. - B. Use the storage takeover command on the storage controller that contains my_data_vol.
- C. Use the wafliron command against my_data_vol to solve the inconsistency on the volume.
- D. Determine the root cause behind the inconsistency before attempting any recovery procedure.
Answer: A
NEW QUESTION # 49
You are trying to deploy a Connector in the AWScloud from NetApp Cloud Manager. The deployment fails
and shows the message 'Insufficient permissions to deploy Cloud Connector". You have verified the AWS
access key and the AWS secret key.
In this scenario, what Is the reason that the deployment failed?
- A. The user lacks the permission to deploy within Cloud Manager.
- B. The required Identity and Access Management (IAM) policies were not Installed.
- C. No AWS Marketplace subscription is associated with Cloud Manager.
- D. The Connector can be deployed only inAWS GovCloud (US).
Answer: A
NEW QUESTION # 50
......
Network Appliance NS0-593 exam is designed to test the skills and knowledge of individuals who wish to become NetApp Certified Support Engineers. NS0-593 exam covers various topics related to NetApp ONTAP storage systems, and successful completion of the exam is a major step towards obtaining the NCSE ONTAP Specialist certification. Candidates who pass the exam will be able to demonstrate their proficiency in managing, troubleshooting, and supporting NetApp ONTAP storage systems, which can help them to advance their careers in the IT industry.
Pass Your Network Appliance Exam with NS0-593 Exam Dumps: https://www.getvalidtest.com/NS0-593-exam.html
NS0-593 Exam Dumps PDF Updated Dump from GetValidTest Guaranteed Success: https://drive.google.com/open?id=1fOuF8Jqe7_QtavN8NhkQANcNPHjBcfqc